Products

We manufacture 16 product families for aluminium and steel plants

We design and manufacture all our equipment, from melting furnaces to heat treatment furnaces and from casting lines to automation panels, at our plant in Çayırova, Kocaeli. The pages below give the capacity, dimensions and options of each machine; you can find where the equipment sits within the line on the solution pages.

Aluminium products

Aluminium equipment, from furnace to end of line

Melting and Holding Furnaces
Furnace room

Melting and Holding Furnaces

Reverberatory body, single- or twin-chamber, from 500 kilograms up to 60 tonnes. With a regenerative burner, the heat that would leave through the flue is returned to the combustion air.

EXPLORE
Degassing
Molten metal

Degassing

The rotary degasser, ceramic filter box and launder system go in between the furnace and the pit as a single assembly. Hydrogen and inclusions are removed before they reach casting.

EXPLORE
Casting
Casting pit

Casting

The vertical casting machine, mould table and cooling water control are built together. Billet diameter and pit depth are determined by your product range.

EXPLORE
Extrusion Billet & Die Heating
Pre-press

Extrusion Billet & Die Heating

A gas-fired or induction heater that brings the billet to the temperature the press requires, with a die furnace alongside. It works as a single line together with the hot shear unit.

EXPLORE
Homogenisation
Billet furnace

Homogenisation

A furnace that evens out the internal structure of the cast billet, with a rapid cooling chamber. The temperature difference in every corner of the load is measured individually.

EXPLORE
Heat Treatment
T5 / T6

Heat Treatment

Solution treatment, quench and ageing furnaces in basket or hanger layouts. Air circulation is designed around the geometry of the part being treated.

EXPLORE
Sheet & Foil Annealing Furnace
Coil annealing

Sheet & Foil Annealing Furnace

Bogie hearth or bell-type furnaces for coil and sheet annealing. The air flow rate into the coil is set so that it leaves no marks on the surface.

EXPLORE
Charging & Dross Removal Systems
Furnace equipment

Charging & Dross Removal Systems

Charging car, pusher and dross skimming unit. The whole charge goes in with a single push so that the furnace door stays open for as short a time as possible.

EXPLORE
Test Systems
In-line inspection

Test Systems

Automatic saw and ultrasonic scanning in a single unit: the billet is cut, scanned and the result is recorded. Defective parts are separated within the line.

EXPLORE
Automatic Billet Cutting
Cutting and stacking

Automatic Billet Cutting

A saw that cuts long billet to length, followed by weighing and stacking. Kerf allowance and chips are calculated so that the length tolerance is held.

EXPLORE
Automatic Loading & Unloading
Along the line

Automatic Loading & Unloading

With conveyors, transfer cars and robot grippers, the furnace front runs unmanned. Forklift waiting comes straight off the cycle time.

EXPLORE

We answer frequently asked questions
about our products

Every product family has reference dimensions, but furnaces and machines are engineered to the plant’s capacity, charging profile and site dimensions. Catalogue values are a starting point; the delivered system is specific to the plant.

Design, manufacturing, installation, automation and commissioning all come from the same team; operator training is part of commissioning. Whether you want a single piece of equipment or the whole line, it is delivered under single-source responsibility.

Yes. Parts such as furnace cars and door mechanisms are manufactured by taking measurements from the existing part; combustion system and automation refurbishments are also carried out on other brands’ equipment.

Four pieces of information start the process: target capacity, the alloys you process, site dimensions and energy infrastructure (gas/electricity). If any information is missing, we clarify it together with a site survey.

Yes. The aluminium systems catalogue covers the entire product programme; the summary version gives the main groups and capacity ranges. You can view or download them from the Catalogues page.

Let’s choose the right equipment together

Let’s start from your line, not from the catalogue

Capacity, alloy, shift pattern and site dimensions: we do not select a machine before we know them. Tell us about your existing line, and we will prepare the quotation accordingly.

Request a Quote

From design to commissioning, we carry out every step with our own team